QCad 3.22.0 keyboard shortcuts

QCad 3.22.0

Zeynel - - Shortcuts

1 comment

0	E then G	Parallel curve (through point)
0	E then Q	Inscribed in quadrilateral

0	P then L	Draw polyline
-1	O then G	Polyline segments
0	O then C	Polyline from selection
0	O then L	Partial polyline along selection
0	O then A	Insert node
0	or O then I
0	O then P	Append nodes
0	O then D	Delete nodes
0	O then B	Delete segments between two nodes
0	O then T	Trim segments
0	O then R	Relocate start point
0	O then X	Change segment type
0	O then Q	Offset
0	O then M	Morph
0	O then S	Simplify
0	O then N	Normalize polylines
0	O then E	Logically close polylines
0	O then J	Logically open polylines

0	M then V	Move / copy
-1	R then O	Rotate
0	S then Z	Scale
0	M then I	Mirror
0	F then H	Filp horizontal
0	F then V	Flip vertical
0	M then R	Move and rotate
0	R then 2	Rotate two
0	A then E	Align reference points
0	M then A	Align
0	O then F	Offset (with distance)
0	O then H	Offset (with point)
0	R then M	Trim
0	or X then T
0	T then M	Trim both
0	L then E	Lengthen / shorten
0	S then S	Stretch
0	C then L,R	Clip to rectangle
0	C then H	Chamfer / bevel
0	R then N	Round
0	D then I	Divide
0	M then S	Split entities
0	D then 2	Break out segment
1	B then 2	Break out manual
0	A then X	Auto trim
0	D then 3	Break out gap
0	R then V	Reverse
0	M then T	Edit text
0	M then H	Edit hatch
0	X then P	Explode

0	M then F	Bring to front
0	M then B	Send to back
0	R then D	Reorder

0	M then D	Detect duplicates
0	M then Z	Detect zero-length entities
Advertisement

0	P then R	Orthographic projection (cylindirical)
0	P then J	Isometric projection
0	P then C	Isometric projection (cylindirical)
0	M then X	Matrix transformation

0	X then P	Explode
0	B then V	Toggle visibility
0	B then S	Show all blocks
0	B then H	Hide all blocks
0	B then A	Add empty block
0	B then C	Create block from selection
0	B then L	Add layout block
0	B then R	Remove block
0	B then P	Purge unused blocks
0	B then N	Rename block
0	B then E	Edit block
0	B then D	Edit block from reference
0	B then Y	Copy block
0	E then M	Return to main drawing
0	B then +	Select block references
0	B then -	Deselect block references
0	B then I	Insert block
0	B then T	Create library item

0	U then A	Define block attribute
0	U then Y	Synchronize attributes

0	Y then V	Toggle visibility
0	Y then F	Toggle frozen status
0	Y then L	Toggle lock status
0	Y then O	Show only active
0	Y then S	Show all layers
1	Y then H	Hide all layers
0	Y then W	Thaw all layers
0	Y then Z	Freeze all layers
0	Y then K	Lock all layers
0	Y then N	Unlock all layers
0	Y then A	Add layer
0	Y then U	Add sublayer
0	Y then T	Create layer from selection
0	Y then R	Delete layer
0	Y then P	Purge unused layers
0	Y then E	Edit layer
0	Y then +	Select layer
0	or Y then C
0	Y then -	Deselect layer
0	or Y then D

0	Ctrl + ↑ Shift + W	Close all
0	Ctrl + →	Next
0	or Ctrl + Page Up
0	Ctrl + ←	Previous
0	or Ctrl + Page Down
0	Ctrl + ↑ Shift + F	Full screen

0	G then E	Script shell
0	X then C	Run script

0	S then F	Free
0	S then G	Grid
0	S then E	End
0	S then T	On entity
0	S then U	Perpendicular
0	S then B	Tangential
0	S then C	Center
0	S then R	Reference
0	S then M	Middle
0	S then N	Middle manual
0	S then D	Distance
0	S then H	Distance manual
0	S then I	Intersection
0	S then Y	Intersection manual
0	S then A	Auto
0	S then X	Coordinate
0	S then O	Polar coordinate
0	. then X	X/Y from points
0	. then Y	Y/X from points
0	S then K	Center of selection
0	E then N	Restrictions off
0	E then O	Restrict orthogonally
0	E then H	Restrict horizontally
0	E then V	Restrict vertically
0	E then L	Restrict angle or length
0	R then Z	Set relative zero
0	R then L	Lock relative zero
0	S then Q	Lock snap
Source: Qcad (pdf)

Share this page on:

Is this page helpful?

1 0

Please temporarily enable JavaScript in your browser to post text. This is to avoid comment bots. We're sorry for inconvenience. #commentForm { display: none; }